10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
|
# the path points to where megatest.db exists
[refareas]
area1 /tmp/oldarea/megatest
[include ./configs/mt_include_1.config]
[dashboard]
pre-command xterm -geometry 180x20 -e "
post-command |& tee results.log ;echo Press any key to continue;bash -c 'read -n 1 -s'" &
testsort -event_time
[misc]
home #{shell readlink -f $MT_RUN_AREA_HOME}
parent #{shell readlink -f $MT_RUN_AREA_HOME/..}
testsuite #{shell basename $MT_RUN_AREA_HOME}
[tests-paths]
1 #{get misc parent}/simplerun/tests
[setup]
# turn off faststart, put monitor.db in MT_RUN_AREA_HOME/db
# and set the dbdir to /var/tmp/$USER/mt_db to enable keeping
# the raw db in /var/tmp/$USER
#
faststart no
monitordir #{getenv MT_RUN_AREA_HOME}/db
dbdir #{getenv MT_RUN_AREA_HOME}/db
# sync more aggressively to megatest-db
megatest-db yes
# Set launchwait to no to use the more agressive code that does not wait for the launch to complete before proceeding
# this may save a few milliseconds on launching tests
# launchwait no
waivercommentpatt ^WW\d+ [a-z].*
incomplete-timeout 1
# wait for runs to completely complete. yes, anything else is no
run-wait yes
# If set to "default" the old code is used. Otherwise defaults to 200 or uses
# numeric value given.
#
|
|
|
>
>
|
>
>
>
>
|
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
|
# the path points to where megatest.db exists
[refareas]
area1 /tmp/oldarea/megatest
[include ./configs/mt_include_1.config]
[dashboard]
# pre-command xterm -geometry 180x20 -e "
# post-command |& tee results.log ;echo Press any key to continue;bash -c 'read -n 1 -s'" &
testsort -event_time
[misc]
home #{shell readlink -f $MT_RUN_AREA_HOME}
parent #{shell readlink -f $MT_RUN_AREA_HOME/..}
testsuite #{shell basename $MT_RUN_AREA_HOME}
[tests-paths]
1 #{get misc parent}/simplerun/tests
[setup]
# turn off faststart, put monitor.db in MT_RUN_AREA_HOME/db
# and set the dbdir to /var/tmp/$USER/mt_db to enable keeping
# the raw db in /var/tmp/$USER
#
faststart no
monitordir #{getenv MT_RUN_AREA_HOME}/db
dbdirdefn /tmp/#{getenv USER}/#{getenv MT_TESTSUITE_NAME}/db
dbdirmkdir #{scheme (create-directory "#{get setup dbdirdefn}" #t)}
dbdir #{get setup dbdirdefn}
# sync more aggressively to megatest-db
megatest-db yes
# Set launchwait to no to use the more agressive code that does not wait for the launch to complete before proceeding
# this may save a few milliseconds on launching tests
# launchwait no
waivercommentpatt ^WW\d+ [a-z].*
incomplete-timeout 1
# wait 0.5 seconds between launching every process
#
launch-delay 0.5
# wait for runs to completely complete. yes, anything else is no
run-wait yes
# If set to "default" the old code is used. Otherwise defaults to 200 or uses
# numeric value given.
#
|
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
|
((none) "nbfake") \
((openlava) "bsub -o $MT_LINKTREE/$MT_TARGET/$MT_RUNNAME.$MT_TESTNAME-$MT_ITEM_PATH.log") \
((sleeprunner) "sleeprunner") \
(else "nbfake"))}
# launcher bsub -q priority -o $MT_TEST_RUN_DIR/openlava.log
# launcher #{shell if which bsub > /dev/null;then echo bsub -q priority -o openlava.log;else echo sleeprunner;fi}
# launcher nbfake
[configf:settings trim-trailing-spaces yes]
# Override the rollup for specific tests
[testrollup]
runfirst ls
|
|
|
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
|
((none) "nbfake") \
((openlava) "bsub -o $MT_LINKTREE/$MT_TARGET/$MT_RUNNAME.$MT_TESTNAME-$MT_ITEM_PATH.log") \
((sleeprunner) "sleeprunner") \
(else "nbfake"))}
# launcher bsub -q priority -o $MT_TEST_RUN_DIR/openlava.log
# launcher #{ shell if which bsub > /dev/null;then echo bsub -q priority -o openlava.log;else echo sleeprunner;fi}
# launcher nbfake
[configf:settings trim-trailing-spaces yes]
# Override the rollup for specific tests
[testrollup]
runfirst ls
|